Shop for artificial dialysis

Routine hemodialysis machine

2

Female

I. General Requirements: 100% new equipment. Year of manufacture: 2025 or later. Meets quality and safety certifications: EC, ISO 13485. Operating environmental conditions: Ambient temperature: 15-35°C. Relative humidity: 35-80%. Water supply temperature: 5-30°C. Pressure: 0.1 - 0.73 Mpa. Air pressure: 70-106.2 kPa. Power supply: 220V, 50Hz. II. Configuration for each machine: Main unit: 1 unit; RO water system connection set: 1 set; Wastewater system connection set: 1 set; Filter fluid connection set A, B (pre-installed): 1 set; Infusion stand/primer support: 1 unit; Filter holder: 1 unit; Arterial and venous clamp: 1 unit; Power cord (pre-installed): 1 unit; Backup battery (pre-installed): 1 unit; Disinfectant chemical suction rods: 2 units; Ultra-pure fluid filter membrane: 1 unit; English and Vietnamese user manual: 1 set. III. Technical Specifications: Water supply: Inlet water pressure: 0.05 - 0.75 Mpa (0.5 - 7.5 Kgf/cm2). Temperature: 15°C – 30°C (5°C – 30°C with heat exchanger). Drainage height: 60 cm from the floor to the end of the discharge line. Central fluid inlet port. Supply pressure: 5 - 98 kPa. Power supply: Voltage: AC 230V/110V ± 10%, 50/60 Hz. Maximum power: 2000 VA. Operating environment: Temperature: 15 - 35°C. Atmospheric pressure: 795 - 1062 hPa. Humidity: 35 - 80% (non-condensing). Storage: Temperature: 5 - 50°C (no liquid in the drainage line); -10 - 50°C (with liquid in the drainage line). Warning signals: Audible and visual warnings. EXTRACORPOREAL CIRCULATION. Blood pump: 10 - 600 ml/min with 8mm inner diameter blood line. Flow rate from 10 - 300 ml/min with a 6.35 mm inner diameter tubing. Accuracy: ±10%. Tubing diameter: 6.35 and 8.0 mm. Arterial pressure control. Measurement range: -500 mmHg to +500 mmHg. Accuracy: ±10%. Venous pressure control. Measurement range: -500 mmHg to +500 mmHg. Accuracy: ±10%. Transmembrane pressure: Display range: -999 mmHg to +999 mmHg. Air bubble detector. Air bubble detection uses an ultrasonic sensor, integrated with a blood detection sensor at the venous clamp. Heparin Pump: Infusion rate: 0 - 9.9 ml/hour Bolus: 0.5 - 5 ml Usable syringe sizes: 10 - 20 - 30 ml HYDRAULIC SYSTEM Distillation flow rate: 300 - 800 ml/minute. Adjustment increment: 50 ml/minute Accuracy: 0 - 10% of set value Distillation temperature: 34 - 39 °C Distillation conductivity: 130 - 160 mEq/L Stability: 0.3 mS/cm or lower Acetate solution: Mixing ratio: 1/30 - 1/54 Concentration: 130 - 160 mEq/L Bicarbonate solution: Mixing ratio: 1/30 - 1/54 Concentration: 5 - 65 mEq/L Ultra-clean distillation membrane: The membrane cleans the distillation solution before it reaches the infusion chamber. Filter lifespan: - 1200 hours when cleaned with peracetic acid (300 runs); - 1800 hours when cleaned with hot citric acid (450 runs). Cut-off point: 6000 Da. Ultrafiltration: Weight withdrawal rate: 0.0, 0.1 - 5.00 L/hour. Accuracy: ±30g/hour. Full display of treatment parameters: Total ultrafiltration volume, weight withdrawal rate, weight withdrawal time, dialysis time, amount withdrawn, and treatment end time. Blood leak detection sensor: Uses an optical sensor. Setting range: 500 - 500 ppm. Accuracy: ±100 ppm. Detection point 260 ppm (Ht 32%). OTHER FUNCTIONS: Calculates dialysis dose based on patient information (height, weight, age), treatment time, and blood pumping rate. Monitoring via graph throughout the run. Display: Touchscreen display that can rotate around its axis. Backup power: Battery backup in case of power outage. Usage time: ≥30 minutes. WASHING AND DISINFECTION PROGRAMS FOR THE MACHINE: Water wash, warm wash at 32 - 39°C. Hot water wash at 70 - 86°C. Disinfection with hot citric acid at high temperature 70 - 86°C. Descaling with acetic acid at room temperature. Disinfection with peracetic acid. Disinfection with bleach. The machine has various washing programs: daily wash, weekly wash, combined chemical wash. IV. Other requirements: Commitment to providing replacement parts and accessories within 8 years. Warranty period: Minimum 12 months

Nghi Son General Hospital

The technical specifications mentioned above are for reference only. You can offer prices for equipment with equivalent or better specifications.